Showing posts with label Amplifiers. Show all posts
Showing posts with label Amplifiers. Show all posts

Monday, November 3, 2014

Automatic cooler fan for amplifiers

The schematic of an automatic cooler fan for audio amplifiers is given here. The circuit automatically switch ON the cooler fan whenever the temperature of the heat sink exceeds a preset level. This circuit will save a lot of energy because the cooler fan will be OFF when the amplifier is running on low volume. At low volume less heat will be dissipated and it will not trigger the cooler fan ON.

The temperature is sensed using an NTC (negative temperature coefficient) thermistor R2. Junction of thermistor r2 and resistor R1 is connected to the inverting input (pin3) of IC1 which is wired as a comparator. The non-inverting input (pin2) is given with a reference voltage using the preset R3. As temperature increases the resistance of NTC thermistor will drop and so do the voltage across it. When the voltage at the inverting input becomes less than that of the reference voltage (set for a particular threshold temperature) the output of the comparator goes high and switches the transistor Q1 ON. This will activate the relay and the cooler fan will be switched ON. When the temperature decreases the reverse happens. LED D2 will glow when the fan is ON. Diode D1 is a freewheeling diode.

Notes.
The circuit can be assembled on a Vero board.
Use 12V DC for powering the circuit.
The circuit can be calibrated by adjusting the preset R3.
K1 can be a 12V, 200 ohm, SPST relay.
LM311 must be mounted on a holder.
Here continue read..

Tuesday, October 28, 2014

Quadraphonic Amplifiers

This is a four channel amplifier ideally suited in place of utilization with quadraphonic equipment such like a Sound Blaster Live tag. present is rejection volume control,audio levels being in a straight line controlled from the sound tag itself.

Quadraphonic

Component Parts :
D1-D4: 1N4001 (4) 
C1,C20: 1000u CAP (2) 
C2,C11: 47u CAP (2) 
C3,C5,C7,C8,C12,C14,C16,C17,C21,C22: 0.1u CAP (10) 
C4,C6,C13,C15: 10u CAP (4) 
C9,C10,C18,C19: 2200u CAP (4) 
R1,R4,R9,R12: 1M RESISTOR (4) 
R2,R6,R10,R14: 100k RESISTOR (4) 
R3,R5,R11,R13: 1k RESISTOR (4) 
R7,R8,R15,R16: 2R7 RESISTOR (4) 
IC1: 7812 (1) 
IC2,IC3: LM1778N (2) 
SPK1,SPK2,SPK3,SPK4: 8R 2 Watt speakers (4) 

Clarification:
Construction is straight cheeky and is apposite in favor of Verobaord. Overall collect is controlled by the ratio R14/R13 and R6/R5. Used with minor hifi speakers the volume was too loud for my extent so I cut-rate R14 and R6 to 33k. The zobel net formed by R7,C7,R8,C8,R15,C16,R16,C17 prevents instability which can take place with slow spokesperson wires. The input impedance is summit, 1M and if very long input cables are award can pick up sound. Screened cable must come about used, now my folder I used 10k resistors among points A & C, B & C, D & F, E & F. This provides a DC path to ground and top clamor exemption. If instability does occur, at that moment you desire notice sound distortion and the LM1877N will develop into passionate to bit.
associates:
The back of a sound blaster live certificate has colour oblique 3.5mm stereo jacks. The image lower shows a close up of the rear of my Sound Blaster Live tag. in the function of well as colour coding, every connector has an appropriate marking, intended for laid-back connectivity.

The customary output connector is conservational and the rear narrator connector is black. Creative provide utilities and sound mixer for exercise with Windows. Under Linux the helpfulness Gamix can remain used, which allows autonomous volume control instead of all channels.



Here continue read..