Showing posts with label Bass. Show all posts
Showing posts with label Bass. Show all posts

Wednesday, September 24, 2014

Active Bass Enhancer with Correction Circuit for Subwoofers

Active loudspeakers offer the only way f obtaining good bass reproduction from inexpensive or small enclosures.
The design described does not make use, therefore, of large, heavy enclosures to obtaion a good result, but of acoustic feedback. A microphone placed in close proximity of the bass drive unit unfailingly registers every movement of the loud-speaker. It is, of course, important that proper attention is paid to the maximum movement of the speaker.

The microphone output is coupled . into the negative feedback loop ofthe output amplifier. In this way, the input sig- nal to the amplifier is compared with the acoustic signal produced by the speaker. In practice, this arrangement appears to work well only with low-frequency signals. Experiments have shown that if  the microphone is placed about 10 mm from the cone of the woofer, signals at e frequencies of up to 500 Hz are fed back faithfully.

To make absolutely certain of  correct operation, in the present circuit the upper frequency has been set to 300 Hz; above it, the correcting action gradually ceases. Note, however, that the phase behaviour of the loudspeaker is corrected also for signals above 300 Hz. lf the change-over frequency ofthe cross- over filter ofthe loudspeaker lies at 300 Hz, it is advisable to make the cut-off frequency ofthe present circuit, determined by R6-C8, lower than 300 Hz. The gain of lC2 over the operating range of the circuit is 20 dB, which reduces to 0 dB for frequencies above 300 Hz. This amplifier, which provides the correction up to the cut~off point, also serves  as buffer for the microphone signal.

Preset Pl serves to set the signal level on the basis of the power rating of the n outpu amplifier and the efficiency of the microphone. lf this control is set too high, corection is also applied to frequencies above the cut-off point; if it is set too low, little correction will be applied and signals between 20 Hz and 300 Hz will increase along a standard lst order characteristic. The choice of microphone is a matter of some experimentation, particularly with high-power amplifiers.

That used in the proposed subwoofer bass enhancer prototype proved to work well with low-power systems with a relatively low efficiency. If another type is used, make sure that the potential across the microphone is about half the supply voltage. This is arranged by R8 and R9. Also make sure that the cut-off point set by P1-C9 remains well below 20 Hz (no signal at P1 results in an increase of the final amplification). The frequency up to which the microphone signal is compensated is determined by R8-P1-Cm.

 This time-constant must be equal to R6-C8. The present circuit can magnify frequencies down to 20 Hz by roughly 20 dB. Since most loudspeakers cannot cope with that frequency, the circuit includes a 3rd order Butterworth section with a cut-off point of 37 Hz.

This frequency may be altered by changing the values of C1, C2, and C3. This filter prevents the loud-speaker being loaded with signals which it cannot reproduce. The bass correction circuit is of particular use with active loud speaker systems.M2 makes sure that the loudspeaker phase is sh ifted by l80° to prevent positive feedback. This may be done by adding an inverter-buffer before K2. The circuit draws about t5 mA, of which only 0.25 mA is drawn by the microphone.


Here continue read..

Tuesday, September 23, 2014

10W Audio Amplifier With Bass Boost circuit and explanation

High Quality, very simple design, No preamplifier required

This design is based on the 18 Watt Audio Amplifier, and was developed mainly to satisfy the requests of correspondents unable to locate the TLE2141C chip. It uses the widespread NE5532 Dual IC but, obviously, its power output will be comprised in the 9.5 – 11.5W range, as the supply rails cannot exceed ±18V. As amplifiers of this kind are frequently used to drive small loudspeaker cabinets, the bass frequency range is rather sacrificed. Therefore a bass-boost control was inserted in the feedback loopof the amplifier, in order to overcome this problem without quality losses. The bass lift curve can reach a maximum of +16.4dB @ 50Hz. In any case, even when the bass control is rotated fully counterclockwise, the amplifier frequency response shows a gentle raising curve: +0.8dB @ 400Hz, +4.7dB @ 100Hz and +6dB @ 50Hz (referred to 1KHz).

Amplifier with Bass-Boost:10W

10W Bass Boost Amplifier Circuit Diagram

Parts:

P1_________________22K Log.Potentiometer (Dual-gang for stereo)
P2________________100K Log.Potentiometer (Dual-gang for stereo)
R1________________820R 1/4W Resistor
R2,R4,R8____________4K7 1/4W Resistors
R3________________500R 1/2W Trimmer Cermet
R5_________________82K 1/4W Resistor
R6,R7______________47K 1/4W Resistors
R9_________________10R 1/2W Resistor
R10__________________R22 4W Resistor (wirewound)
C1,C8_____________470nF 63V Polyester Capacitor
C2,C5_____________100µF 25V Electrolytic Capacitors
C3,C4_____________470µF 25V Electrolytic Capacitors
C6_________________47pF 63V Ceramic or Polystyrene Capacitor
C7_________________10nF 63V Polyester Capacitor
C9________________100nF 63V Polyester Capacitor
D1______________1N4148 75V 150mA Diode
IC1_____________NE5532 Low noise Dual Op-amp
Q1_______________BC547B 45V 100mA NPN Transistor
Q2_______________BC557B 45V 100mA PNP Transistor
Q3_______________TIP42A 60V 6A PNP Transistor
Q4_______________TIP41A 60V 6A NPN Transistor
J1__________________RCA audio input socket

Power Supply :Power

Power Supply Circuit Diagram

Power supply parts:

R11_________________1K5 1/4W Resistor
C10,C11__________4700µF 25V Electrolytic Capacitors
D2________________100V 4A Diode bridge
D3________________5mm. Red LED
T1________________220V Primary, 12 + 12V Secondary 24-30VA Mains transformer
PL1_______________Male Mains plug
SW1_______________SPST Mains switch

Notes:

  • Can be directly connected to CD players, tuners and tape recorders.
  • Schematic shows left channel only, but C3, C4, IC1 and the power supply are common to both channels.
  • Numbers in parentheses show IC1 right channel pin connections.
  • A log type for P2 will ensure a more linear regulation of bass-boost.
  • Do not exceed 18 + 18V supply.
  • Q3 and Q4 must be mounted on heatsink.
  • D1 must be in thermal contact with Q1.
  • Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
  • Set the volume control to the minimum and R3 to its minimum resistance.
  • Power-on the circuit and adjust R3 to read a current drawing of about 20 to 25mA.
  • Wait about 15 minutes, watch if the current is varying and readjust if necessary.
  • A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 &C4. Connect C9 to the output ground.
  • Then connect separately the input and output grounds to the power supply ground.

Technical data:
Output power:
10 Watt RMS into 8 Ohm (1KHz sinewave)
Sensitivity:
115 to 180mV input for 10W output (depending on P2 control position)
Frequency response:
See Comments above
Total harmonic distortion @ 1KHz:
0.1W 0.009% 1W 0.004% 10W 0.005%
Total harmonic distortion @ 100Hz:
0.1W 0.009% 1W 0.007% 10W 0.012%
Total harmonic distortion @ 10KHz:
0.1W 0.056% 1W 0.01% 10W 0.018%
Total harmonic distortion @ 100Hz and full boost:
1W 0.015% 10W 0.03%
Max. bass-boost referred to 1KHz:
400Hz = +5dB; 200Hz = +7.3dB; 100Hz = +12dB; 50Hz = +16.4dB; 30Hz = +13.3dB
Unconditionally stable on capacitive loads

Elektor 303 Circuit
Practical Arduino
Elektor05-2010
Elektor05-2010
Elektor05-2010
Nuts Volts 06-2010
Nuts Volts 06-2010
Here continue read..