Showing posts with label microphone. Show all posts
Showing posts with label microphone. Show all posts

Wednesday, November 19, 2014

Preamplifier Microphone with 2 Transistor

Microphone preamplifier or often known as mic preamp can be made use simplemicrophone preamplifier circuit as follows. 2 microphone preamplifier circuit uses 2transistors are PNP and NPN transitor amplifier.

Front of the microphone amplifier orpreamplifier microphone 2 transistor uses a system of dc negative feedback through R6which serves to provide stability strengthening. Level output signal from the microphonepreamplifier is controlled by potentiometer P1. Input signal that can be responded well by this microphone preamplifier is 0.2 - 200mV and 1V RMS output will result.





   Component List      P1 2k2
     R1, R2, R3 100K 1/4W
     R4 8K2 1/4W
     R5 68R 1/4W
     R6 6K8 1/4W
     R7, R8 1K 1/4W
     R9 150R 1/4W
     C1 1uF 63V
     C2, C3, C4 100uF 25V
     C5 22uF 25V
     Q1 BC560C
     Q2 BC550C
 
Microphone preamplifier circuit two transistors in the show above is preampmic suitable for home audio system on the stereo. This microphone preamplifier circuit requires supply voltages 9Vdc.  
Here continue read..

Wednesday, October 29, 2014

Dual Mode Microphone Pre Amplifier

This is a microphone pre-amp which I designed intended for function with a SoundBlaster(TM) AWE 64 charge sound license; but it be supposed to exist apt for one compatible tag otherwise PC audio input which provides a 5 Volt supply (via a 2k2, or else thereabouts, built-taking part in current-limiting resistor) by the side of the ring call of a stereo jack plug inserted into the "Mic In" socket of the license/PC. (N.b. it has lone been tested with the AWE 64 certificate.)

The circuit has the following skin tone :
(1) It wish without human intervention detect whether a mike plugged into it is of the electret (condenser) otherwise dynamic type and will switch sandwiched between respective "low-addition" and "far above the ground-gain" modes accordingly. The van-detection relies on help of a stereo plug fitted to an electret mike and use of a mono plug fitted to a dynamic mike.
(2) It is powered just by the 5 Volt existing next to the "Mic in the field of" socket.
(3) It is trivial adequate to happen housed in a standard plastic 35mm film flask (remember folks?).
(4) A trimmer allows the next of kin win intended for the two microphone types to be adjusted.
(5) The gain is sufficient to award something like 60mV summit-to-peak next to the "Mic In" socket, obligatory for complete recording level at home WaveStudio.
(6) In conjunction with the licenses built-in input amplifier, the circuit provides a lifeless frequency response done the audio range, with -3dB points on <10 hz and 19 khz.
(7) Input impedance > 10k. Output impedance <1k

Dual-Mode

Component Values :
R1 = R7 = 4k7; R2 = R3 = 47k; R4 = 39k; R5 = R6 = 100k; R8 = 220; R9 = 10k; R10 = 2k2 (all 1/8 Watt). VR1 = 10k
horizontal pre-set. C1 = 47uF; C2 = C3 = C4 = 10uF (all 10V or greater, miniature radial electrolytics). Tr1 = Tr2 = Tr3 = Tr4 = Tr5 = BC108, BC184, BC547, ZTX337 or similar low-power (preferably low noise) NPN transistor
Here continue read..

Tuesday, October 28, 2014

Simple condenser microphone circuit

This is a very use full and simple circuit diagram for amplifying weak signal from a capacitive condenser microphone. You can use this circuit for sound sensing applications and some automatic robotic sensors. We have already posted an Efficient audio amplifier circuit using 1895 IC; it is somewhat complicated and suitable for very sensitive applications. But this condenser microphone DIY audio sound amplifier is very small and simple to implement because it uses only two BC547 transistors and some discrete components. You can construct this circuit with minimum of $2 price. This circuit apt for cheap amplification purposes in electronics such as pre amplifier for FM Transmitter.
Circuit diagram


Components required
    Resistors (2.2kΩ; 3.3kΩ; 470kΩ; 220kΩ; 1.2kΩ)
    Capacitors (0.1µF x 2; 10µF,16V)
    Transistors (BC547 x 2)
    Condenser mic
    Speaker (8Ω, ½ Watt)

Working mini audio amplifier 
The circuit is alienated into three divisions: Condenser mic, Audio amplifier and loudspeaker.
    Condenser mic is a type of capacitive audio sensor (audio transducer) that converts the sound (audio) signal into electrical signals.
    These electrical signals are too weak so it is amplified by the amplifier unit. The amplified output is obtained across the speaker.
    The output of condenser mic is coupled via a coupling capacitor of 0.1µF, the purpose of this capacitor is to remove DC contents in the audio signal.
    A 2.2kΩ resistor is used to give the required biasing to the condenser microphone.
    Transistor Q1 is configured as collector to base biasing mode. This is accomplished via 470kΩ resistance. This resistor provides negative feedback to the transistor Q1.
    The output of Q1 becomes available at the collector (across 3.3kΩ resistor), which is the input to the transistor Q2 via a 0.1µF capacitor. The capacitor removes DC voltages due to the biasing of Q1.
    Transistor Q2 is configured as fixed bias using 220kΩ resistor. It also provides further amplification.
    The amplified output from Q2 is available across the 1.2kΩ resistor.
    The 10µF electrolytic capacitor also used to block the DC voltages associated with the biasing of transistor Q2.
    Use 8Ω, ½ watt speaker to hear the amplified signal.
Here continue read..

Saturday, October 25, 2014

Compressor For Electret Microphone Diagram Circuit

The ‘FM Remote Control Receiver’ (available on this website in Infra-red circuits section) has a connector where an analogue output is made available. To make a simple intercom or P.A. system the associated transmitter needs a microphone pre-amplifier that outputs a signal at the correct level. And that is exactly the function of this circuit. Actually, this design is adapted from a circuit published last year (‘AM Modulator for Intercom’). A few things have been changed so that it can work with the 5 V supply from the transmitter module. The OTA (IC1) used here is the single version (CA3080), which has slightly different characteristics from the dual CA3280.


Compressor for Electret Microphone

The quad opamp is the same rail-to-rail TS924IN, made by ST. The turnover frequency of the filter (3rd order 1 dB Chebyshev) has been increased slightly to improve the intelligibility of speech and is now about 5.5 kHz. The filter now amplifies the signal by a factor of 10. In practice it is possible that due to various tolerances and the fact that the opamp is not perfect, the filter characteristic shows some deviation from that required. In our prototype it was necessary to change R15 into 2k7 to straighten the response curve. The DC current variation at the output of the OTA and the resulting offset variation at the output of current/voltage converter IC2d is such that the gain of IC2d has to be substantially smaller than in the ‘old’ design.

Otherwise the output could easily rise to the supply voltage at low signal levels. The value of R6 has therefore been made smaller by a factor of 10. This has reduced the gain of the circuit by 20 dB, which is compensated for in the filter. The amplitude of the signal from IC2d is fed back as a control current to the OTA by peak rectifier D1/C3 and inverting amplifier IC2b. R7 limits the loading on IC2d. P1 can be used to adjust the amplifier between a fixed gain and maximum compression. Figure A shows clearly what effect the circuit has. 0 dBr corresponds to 100 mV. The maximum gain, with P1 set to maximum compression, is about 48 dB (250 Ω) for small signals.

The minimum gain is about 20 dB (10 Ω). The OTA is then slightly overdriven and the distortion becomes several percent! With a fixed gain selected (P1 shorted) the gain is about 42 dB (125 ×). The middle curve was measured with P1 in its central position. The curve drawn for a fixed gain (the straight line) doesn’t finish at the edge of the graph because the end of the line corresponds to the maximum possible output level, which is 25 dBr (≈1.76 V or 5 / 2√2). Figure B shows the frequency response. The low turnover frequency is mainly determined by C8 (and to a lesser extent by C1) and is about 120 Hz.

The current consumption is about 7 mA When the circuit is battery powered we recommend the use of three AA cells, because the circuit still works perfectly at 4.5 V. If you want to use a higher supply voltage (maximum 12 V for the de TS924IN and 30 V for the CA3080, but you should also think of the voltage across the electret microphone!) you have to keep in mind that the maximum current through R9 (which is IABC) is only 2 mA. When we consider a maximum chosen current of 1 mA and the maximum output voltage of IC2b (half the supply voltage, which is 2.5 V), then the value of R9 should be (2.5 – 0.7) V / 1 mA = 1.8 kΩ. The value of 0.7 V corresponds to the potential between pin 5 and earth.

For a larger safety margin R9 is calculated with the full supply voltage and a current of 2 mA: (5 – 0.7) V / 2 mA = 2k2 (rounded upwards). Of course the regulation will then be different (a little less gain). This circuit and the transmitter module can therefore be fed from the same 5 V supply. Because the transmitter requires a DC offset at its input, a resistor is connected to +5 V via a jumper, which biases the output to half the supply voltage. With the jumper open R17 functions as a load resistor when the output is not connected, because C9 still has to charge up even without a load. If you’re designing a PCB for this compressor then it makes sense to include the transmitter module as well. The current consumption then increases by about 10 mA.
Author: T. Giesberts - Copyright: Elektor Electronics
Here continue read..

Monday, September 15, 2014

Microphone for Computer

Microphone
This schema was submitted by Lazar Pancic from Yugoslavia. The sound card for a PC generally has a microphone input, speaker output and sometimes line inputs and outputs. The mic input is designed for dynamic microphones only in impedance range of 200 to 600 ohms. Lazar has adapted the sound card to use a common electret microphone using this schema. He has made a composite amplifier using two transistors. The BC413B operates in common emitter to give a slight boost to the mic signal. This is followed by an emitter follower stage using the BC547C. This is necessary as the mic and schema and battery will be some distance from the sound card, the low output impedance of the schema and Lcded cable ensuring a clean signal with minimum noise pickup.
Here continue read..