Showing posts with label 2. Show all posts
Showing posts with label 2. Show all posts

Wednesday, November 19, 2014

Preamplifier Microphone with 2 Transistor

Microphone preamplifier or often known as mic preamp can be made use simplemicrophone preamplifier circuit as follows. 2 microphone preamplifier circuit uses 2transistors are PNP and NPN transitor amplifier.

Front of the microphone amplifier orpreamplifier microphone 2 transistor uses a system of dc negative feedback through R6which serves to provide stability strengthening. Level output signal from the microphonepreamplifier is controlled by potentiometer P1. Input signal that can be responded well by this microphone preamplifier is 0.2 - 200mV and 1V RMS output will result.





   Component List      P1 2k2
     R1, R2, R3 100K 1/4W
     R4 8K2 1/4W
     R5 68R 1/4W
     R6 6K8 1/4W
     R7, R8 1K 1/4W
     R9 150R 1/4W
     C1 1uF 63V
     C2, C3, C4 100uF 25V
     C5 22uF 25V
     Q1 BC560C
     Q2 BC550C
 
Microphone preamplifier circuit two transistors in the show above is preampmic suitable for home audio system on the stereo. This microphone preamplifier circuit requires supply voltages 9Vdc.  
Here continue read..

Saturday, November 1, 2014

2 Way Speaker Crossover circuit

The series of crossover is an electronic circuit in which the point to separate the audio sound frequency. objective that only sound with a frequency range that can be accepted speakers are forwarded. less is more like a filter function, so the speakers work optimally.

2 way or 3 way or else, that determines how many channels would be separated voice. Each channel is handled by a single class of speakers. Eg 3 way, the frequency of sound produced by the head unit, separated by crossover as a low freq (big size distinguished speaker better known as the subwoofer), medium freq (medium speakers), usually in the middle) and hi freq (small speakers I would call a tweeter) Let me better sound and reduce noise.

Schematic 2 Way Speaker Crossover
Here continue read..

Monday, October 13, 2014

2N3055 and LM723 3 30 V 2 5 A Stabilized power supply


This is a very useful project for anyone working in electronics. It is a versatile power supply that will solve most of the supply problems arising in the everyday work of any electronics work shop. It covers a wide range of voltages being continuously variable from 30 V down to 3 V. The output current is 2.5 A maximum, more than enough for most applications. The circuit is completely stabilised even at the extremes of its output range and is fully protected against short-circuits and overloading.

——————————————————————————–
Technical Specifications – Characteristics
Input voltage: 24V DC
Output current: 2.5 A
Output volytage: 3-30V DC
——————————————————————————–

How it Works
The power supply is using a well known and quite popular VOLTAGE STABILIZER IC the LM 723. The IC can be adjusted for out put voltages that vary continuously between 2 and 37 VDC and has a current rating of 150 mA which is of course too low for any serious use. In order to increase the current handling capacity of the circuit the output of the IC is used to drive a darlington pair formed by two power transistors the BD 135 and the 2N3055. The use of the transistors to increase the maximum current output limits the range of output voltages somewhat and this is why the circuit has been designed to operate from 3 to 30 VDC. The resistor R5 that you see connected in series with the output of the supply is used for the protection of the circuit from overloading. If an excessively large current flows through R5, the voltage across it increases and any voltage greater than 0.3 V across it has as a result to cut the supply off, thus effectively protecting it from overloads. This protection feature is built in the LM 723 and the voltage drop across R5 is sensed by the IC itself between pins 2 and 3. At the same time the IC is continuously comparing the output voltage to its internal reference and if the difference exceeds the designer’s standards it corrects it automatically. This ensures great stability under different loads. The potentiometer P1 is used to adjust the out put voltage at the desired level. If the full range from 3 to 30 V is desired then you should use a mains transformer with a secondary winding having a rating of at least 24 V/3 A. If the maxi mum voltage output is not desired you can of course use a transformer with a lower secondary voltage output. (However, once rectified the voltage across the capacitor C2 should exceed by 4-5 volts the maximum output expected from the circuit.
Parts List
R1 = 560R 1/4W C1 = 100nF
R2 = 1,2 K 1/4W C2 = 2200uF 35-40V
R3 = 3,9 K 1/4W C3 = 100 pF
R4 = 15K 1/4W C4 = 100uF/ 35V
R5 = 0,15R 5W

D = B40 C3300/2200, 3A rectifier bridge
P1 = 10K potesiometer TR1 = BD 135
IC = LM723 TR2 = 2N3055

Here continue read..

Sunday, August 31, 2014

Simple 12 Volt 2 A Switching Power Supply Wiring diagram Schematic

This is a Simple 12 Volt / 2 A Switching Power Supply Circuit Diagram. The schema 12 volt / 2 A switching power supply in the above scheme is not too complicated. At the output of this block provides a stable 12 V and maximum current 2A. Power supply units are quite compact and is suitable for debugging schemes, as well as a permanent resource for stationary devices, including power for the logic electronics for the home-made ​​CNC machine tools. 

12 Volt / 2 A Switching Power Supply Circuit Diagram


12
 
 Transformer is available in the free market and avoids the hassle of having to self-winding. The diode bridge BR 1 of any given voltage and current of 2A. All other elements in the high part of the schema are designed by the same voltage, taking into account the mains. The scheme of 12 volt / 2 A switching power supply operates from the high voltage network, to be observed when mounting accuracy and caution when using. It is desirable to block the finished board to “pack” in the body. 

Sourced By :  powersupply88
Here continue read..

Thursday, August 28, 2014

2 x 75 W Audio Power Amplifier TDA7575

Features:

  • DMOS POWER OUTPUT
  • NON-SWITCHING HI-EFFICIENCY
  • SINGLE-CHANNEL 1Ω DRIVING CAPABILITY
  • HIGH OUTPUT POWER CAPABILITY 2x28W/
  • 4Ω @ 14.4V, 1KHZ, 10% THD, 2x40W/4Ω EIAJ
  • MAX. OUTPUT POWER 2x75W/2Ω, 1x150W/1Ω
  • SINGLE-CHANNEL 1Ω DRIVING CAPABILITY
  • 84W UNDISTORTED POWER
  • FULL I2C BUS DRIVING WITH 4 ADDRESS
  • ST-BY, PLAY/MUTE, GAIN 12/26dB, FULL
  • DIGITAL DIAGNOSTIC
  • POSSIBILITY TO DISABLE THE I2C
  • DIFFERENTAL INPUTS
  • FULL FAULT PROTECTION
  • DC OFFSET DETECTION
  • TWO INDEPENDENT SHORT CIRCUIT 
  • CLIPPING DETECTOR PIN WITH SELECTABLE THRESHOLD (2%/10%)
  • ST-BY/MUTE PINS
Block Diagram:
Block Diagram

Here continue read..