Showing posts with label watt. Show all posts
Showing posts with label watt. Show all posts

Friday, November 14, 2014

INVERTER CIRCUIT 100 WATT

Inverter is a small circuit which will convert the direct current (DC) to alternating current (AC). The power of a battery is converted in to’ main voltages’ or AC power. This power can be used for electronic appliances like television, mobile phones, computer etc. the main function of the inverter is to convert DC to AC and step-up transformer is used to create main voltages from resulting AC.

Block Diagram of Inverter



In the block diagram battery supply is given to the MOSFET driver where it will convert DC to AC and the resulting AC is given to the step up transformer from the step up transformer we will the get the original voltage.

Main Components

CD4047 : CD4047 is a multi vibrator with very low power consumption designed by TEXAS INSTRUMENTS.it can operate in monostable multivibrator and also astable multivibrator.in the astable multivibrator mode it can operate in free running or gatable modes and also provides good astable frequency stability. It can generate 50% duty cycle which will create a pulse, which can be applied for inverter circuit. This is mainly used in frequency discriminators, timing circuits frequency divisions etc.

IRF540 : IRF540 is a N-channel enhanced mode silicon gate field effect transistor (MOSFET).they are mainly used in switching regulators, switching converters relay drivers etc. the reason for using them in the INVERTER circuit is the because it is a high switching transistor , can work in very low gate drive power and have high input impedance.

IRF540 Symbol



Circuit Diagram



Explanation

  • In the circuit diagram we can observe that 12V battery is connecter to the diode LED and also connected to the pin8 of the IC 4047 which is VCC or power supply pin and also to pin 4 and 5 which are astable and  complement astable of  the IC. Diode in the circuit will help not give any reverse current, LED will work as a indicator to the battery is working or not.
  • IC CD4047 will work in the astable multivibrator mode. To work it in astable multivibrator mode we need an external capacitor which should be connected between the pin1 and pin3. Pin2 is connected by the resistor and a variable resistor to change the change the output frequency of the IC. Remaining pins are grounded .The pins 10 and 11 are connected to the gate of the mosfets IRF540. The pin 10 and 11 are Q and ~Q from these pins the output frequencies is generated with 50% duty cycle.
  • The output frequency is connected to the mosfets through resistor which will help to prevent to the loading of the mosfets. The main AC current is generated by the two mosfets which will act as a two electronic switches. The battery current is made to flow upper half or positive half of the primary coil of transformer through Q1 this is done when the pin 10 becomes high and lower half or negative half is done by opposite current flow through the primary coil of transformer, this is done when pin 11 is high. By switching the two mosfets current is generated.
  • This AC is given to the step up transformer of the secondary coil from this coil only we will get the increased AC voltage , this AC voltage is so high; from step up transformer we will get the max voltage. Zenor diode will help avoid the reverse current.

NOTE : The generated AC is not equal to the normal AC mains or house hold current. You cannot use this voltage for pure electric appliances like heater, electric cooker etc. Because of the fast switching of mosfets heat is dissipated which will effect the efficiency, use heat sink to remove this problem.
Here continue read..

Thursday, November 13, 2014

8 Watt Audio Power Amplifier Schematic

Here is the schematic for an 8 watt audio power amplifier. This amp can be used as a simple booster, the heart of a more complicated amplifier or used as a guitar amp. It is very small and portable unit and can be powered through 12V battery. I built the circuit on a Vero Board and had to add extra inductors, capacitors and resistors to prevent oscillation.

Circuit diagram:
 8 watt audio power amplifier schematic circuit diagram
8 Watt Audio Power Amplifier Circuit Diagram


Parts:R1 = 47K
R2 = 2.2R/1W
R3 = 220R/1W
R4 = 2.2R/1W
C1 = 100nF-63V
C2 = 10uF-25V
C3 = 470uF-25V
C4 = 2000uF-25V
C5 = 100nF-63V
IC1 = LM383
SPKR = 4ohm/8W

Notes:
  • IC1 must be installed on a heat sink.
  • C1 is for filtering and to prevent oscillation and should not be omitted.
  • The circuit can be built on a Vero Board, universal solder board or PC board, the PC board is preferred.
  • The circuit draws about 880Ma at 12 V.
  • By swapping the values of R2 and R3; you can turn this amplifier into a guitar amp with no preamp required.
  • If you cant find 2000uF, then replace C4 with a 2200uF unit.
  • If you add a 0.2uF capacitor in series with a 1 ohm resistor to the output you can prevent oscillation of the circuit under certain conditions.
Here continue read..

Wednesday, November 12, 2014

45 Watt Class B Audio Power Amplifier

45W into 8 Ohm - 69W into 4 Ohm, Easy to build - No setup requiredThese goals were achieved by using a discrete-components op-amp driving a BJT complementary common-emitter output stage into Class B operation. In this way, for small output currents, the output transistors are turned off, and the op-amp provides all of the output current. At higher output currents, the power transistors conduct, and the contribution of the op-amp is limited to approximately 0.7/R11. The quiescent current of the op-amp biases the external transistors, and hence greatly reduces the range of crossover.

The idea sprang up from a letter published on Wireless World, December 1982, page 65 written by N. M. Allinson, then at the University of Keele, Staffordshire. In this letter, op-amp ICs were intended as drivers but, as supply voltages up to +/- 35V are required for an amplifier of about 50W, the use of an op-amp made of discrete-components was then considered and the choice proved rewarding.

The discrete-components op-amp is based on a Douglas Self design. Nevertheless, his circuit featured quite obviously a Class A output stage. As for proper operation of this amplifier a Class B output stage op-amp is required, the original circuit was modified accordingly. Using a mains transformer with a secondary winding rated at the common value of 25 + 25V (or 24 + 24V) and 100/120VA power, two amplifiers can be driven at 45W and 69W output power into 8 and 4 Ohms respectively, with very low distortion (less than 0.01% @ 1kHz and 20W into 8 Ohms).

This simple, straightforward but rugged circuit, though intended for any high quality audio application and, above all, to complete the recently started series of articles forming the Modular Preamplifier Control Center, is also well suited to make a very good Guitar or Bass amplifier. Enjoy!Circuit diagram:
45
45W Class-B Amplifier Circuit Diagram
Parts:R1______________18K - 1/4W Resistor
R2_______________3.9K - 1/4W Resistor
R3,R6____________1K - 1/4W Resistors
R4_______________2.2K - 1/4W Resistor
R5______________15K - 1/4W Resistor
R7______________22K - 1/4W Resistor
R8_____________330R - 1/4W Resistor
R9,R10__________10R - 1/4W Resistors
R11,R12_________47R - 1/4W Resistors
R13_____________10R - 1W Resistor

C1_______________1µF - 63V Polyester Capacitor
C2_____________470pF - 63V Polystyrene or Ceramic Capacitor
C3______________47µF - 25V Electrolytic Capacitor
C4______________15pF - 63V Polystyrene or Ceramic Capacitor
C6_____________220nF - 100V Polyester Capacitor
C6_____________100nF - 63V Polyester Capacitor

D1,D2,D3,D4___1N4148 - 75V 150mA Diodes

Q1,Q2________BC560C - 45V 100mA Low noise High gain PNP Transistors
Q3,Q4________BC556 - 65V 100mA PNP Transistors
Q5___________BC546 - 65V 100mA NPN Transistor
Q6___________BD139 - 80V 1.5A NPN Transistor
Q7___________BD140 - 80V 1.5A PNP Transistor
Q8__________2N3055 - 60V 15A NPN Transistor
Q9__________MJ2955 - 60V 15A PNP Transistor
Power supply :
power
Power Supply Circuit Diagram
Parts:R1_______________3.3K - 1/2W Resistor
C1,C2_________4700µF - 50V Electrolytic Capacitors
C3,C4__________100nF - 63V Polyester Capacitors
D1_____________200V 8A Diode bridge
D2_____________5mm. Red LED
F1,F2__________4A Fuses with sockets
T1_____________230V or 115V Primary, 25+25V Secondary 120VA Mains transformer
PL1____________Male Mains plug
SW1____________SPST Mains switchComments:
The main design targets for this amplifier were as follows:
  1. Output power in the 40 - 70W range
  2. Simple circuitry
  3. Easy to locate, low cost components
  4. Rugged performance
  5. No setup
Notes:
  • 2N3055 and MJ2955 transistors were listed for Q8 and Q9 as the preferred types, but many different output transistors can be used satisfactorily: TIP3055/TIP2955, TIP35/TIP36, MJ802/MJ4502 amongst others.
  • Discrete op-amp output transistors Q6 and Q7 do not require any heatsink as their cases remain at ambient temperature. Power transistors Q8 and Q9 should be mounted on a black, finned heatsink as usual.
Technical data:Output power (1KHz sinewave):
  • 45 Watt RMS into 8 Ohms - 69W RMS into 4 Ohms
Sensitivity:
  • 0.81V RMS input for 45W output
Frequency response @ 1W RMS:
  • 15Hz to 23KHz -0.2dB
Total harmonic distortion @ 1KHz:
  • 1W 0.008% 20W 0.008% 45W 0.016%
Total harmonic distortion @10KHz:
  • 1W 0.01% 20W 0.015% 45W 0.025%
Unconditionally stable on capacitive loads 
Here continue read..

Tuesday, September 23, 2014

1000 Watt Mosfet Power Inverter

This power inverter circuit will provide a very stable “Square Wave” Output Voltage. Frequency of operation is determined by a pot and is normally set to 60 Hz. Various “off the shelf” transformers can be used. Or Custom wind your own for best results.

Additional MosFets can be paralleled for higher power. It is recommended to Have a “Fuse” in the Power Line and to always have a “Load connected”, while power is being applied. The Fuse should be rated at 32 volts and should be aproximately 10 Amps per 100 watts of output. The Power leads must be heavy enough wire to handle this High Current Draw! appropriate Heat Sinks Should be used on the RFP50N06 Fets. These Fets are rated at 50 Amps and 60 Volts. Other types of Mosfets can be substituted if you wish.

There ARE Limitations! I have had numerous requests for an Inverter for 1000 watts and Even MORE. Sorry I Don’t feel this is Practical. At 1000 Watts and operating from a 12 Volt Source, the Input Current will be close to 100 AMPS. That would Require a HUGH Size of a Primary Wire.

Mosfet

Here continue read..

Saturday, August 30, 2014

14 Watt car audio amplifier circuit

 
Basic operation of this amplifier is on IC TEA2021 ,
In this circuit minimum require voltage is 4 volts and maximum voltage 25 volts. Power output 14 Watt with 4 Ohm impedance. See this schematic.
Here continue read..