Showing posts with label w. Show all posts
Showing posts with label w. Show all posts
Sunday, November 2, 2014
10 W Audio Amplifier Circuit
This circuit is a general-purpose 10-W audio amplifier for moderate-power PA or modulator use in an AM transmitter. With higher voltages and a change in bias resistors, up to 30 W can be obtained. The Output Stage Amplifier using transistor 2N3055 and MJE2055.
| 10 W Audio Amplifier Circuit Diagram |
Saturday, September 20, 2014
Audio Amplifier MOSFET 200 W
The printed circuit board is very compact , and is composed of two subsets : the command stage and the output stage. All resistors are 1/4 watt 1 % metal film (except if otherwise stated).
Constant current sources of +/- 1 mA are carried out around T5 and T6. The diodes D1 to D6 allow the use of low noise transistors type BC550C and BC560C, the transistors T7 to T10 form the stage driver. The potentiometer P1 allows the adjustment of the quiescient current to 100 mA per output transistor.
The symmetrical power supply is entrusted to a large transformer of 625 VA, 2 * 51 volts + bridge rectifier and 6 reservoir capacitors of 4700 µF, which gives an output voltage of + and - 70 volts per rail.
The output power is 200 Wrms under 8 ohms or 350 Wrms under 4 ohms. Distortion is lower than 0,02 %, damping factor is better than 300, signal-noise ratio is 112 db (balanced A at full power), the input sensitivity is 1,2 volts (200 W under 8 ohms).
Diagram :

The capacitor C3 is not reproduced on the diagram and on the PCB (it is correct).
Proposal of the command stage PCB :

Transistors T9 and T10 must be assembled on a common heatsink with 5° c/w thermal resistance or on the output stage heatsink.
proposal of the output stage PCB :

The points marked A, B and C have to be connected between the two PCB.
The ground (earth) points of PCBs and loudspeaker ground (earth) must compulsorily be connected in star with the 0 Volts of the PSU.
The power transistors must be assembled on a heatsink with a thermal resistance less than 1 ° C/W. They must also be electrically insulated from the heatsink by using a mica insulator + heat-conducting compound or a silicone insulator.
It is possible to use the MOSFET output stage PCB which is also reproduced on the site, but take care with the thermal dissipation of the output transistors (this circuit is perfect for power of 100 Wrms under 8 ohms or 155 Wrms under 4 ohms). It is possible to use two PCBs in parallel to double the number of output transistors, do not place the limitation diodes, the fuses and the RC output circuit on the second PCB.
Bandwidth :
Bandwidth is limited from 5 Hz to 53 Khz (at - 3 db) by the input module (C1, R1, C2, R2). It can be modified according to the application desired. It is useless to increase the bandwidth to the botton (bass) because little useful signal is present at the bottom of the spectrum. In public address sound systems the bandwidth is often limited between 20 and 35 Hz. The loudspeakers are thus protected against too high extreme-bass signals and some more power is available for the remainder of the spectrum.

Thursday, September 18, 2014
1 W Home Stereo Amplifier Wiring diagram Schematic
This is a one watt home stereo amplifier module project using the KA2209 IC from Samsung, which is equivalent to the TDA2822. It operates from 3-12V DC & will work from a battery since the dormant current drain is low. It requires no heat sink for normal use. The input & output are both ground referenced. Maximum output will be obtained with a 12V power supply & 8 ohm speaker, however it is suitable for driving headphones from a supply as low as 3V.
The Specifications of the home stereo amplifier :
The Specifications of the home stereo amplifier :
D.C. input : 3 – 12 V at 200 – 500 mA max
Idle current : approx. 10 mA
Power output : > 1 Watt max. 4-8 ohms, 12V DC
Freq. Resp. : approx. 40 Hz to 200 kHz, 8 ohm, G=10
THD : < 1 % @ 750 mW, 4-8 ohm, 12V
Gain : approx. x10 (20 dB) OR x100 (40dB)
S/N ratio : > 80 dB, G = 20 dB
Sensitivity : < 300 mV, G = 20 dB
Input Impedance : approx. 10 k ohm
Idle current : approx. 10 mA
Power output : > 1 Watt max. 4-8 ohms, 12V DC
Freq. Resp. : approx. 40 Hz to 200 kHz, 8 ohm, G=10
THD : < 1 % @ 750 mW, 4-8 ohm, 12V
Gain : approx. x10 (20 dB) OR x100 (40dB)
S/N ratio : > 80 dB, G = 20 dB
Sensitivity : < 300 mV, G = 20 dB
Input Impedance : approx. 10 k ohm
Description
The gain is adjustable from ten to 100, i.e. twenty to 40 dB. Start with feedback resistors R1 and R3 of 1k ohm, this will give a gain of ten which ought to be adequate for most applications. In case you need more gain, you can remove resistors R1 and R3.This will give a gain of about 100, or 40 dB.The input attenuation can be adjusted by the potentiometer which can be used as a volume control. The IC gain ought to be kept as low as necessary to accomplish full output, with the in put potentiometer and your signal source at maximum.
1 W Home Stereo Amplifier Circuit Diagram
![1]()
1 W Home Stereo Amplifier Circuit Diagram
Voltage Gain = 1+ R1/R2 = 1+R3/R4, however the maximum gain with no outside feedback is about 100, or 40dB. (GdB = 20log Gv)
This will keep the signal to noise ratio as high as feasible. Additional gain provided by the amplifier will reduce the S/N ratio by a similar amount, since the input noise figure is constant. Other values for R1 and R3 of between 1k and 10k ohm can be used if an intermediate gain level is necessary.
This will keep the signal to noise ratio as high as feasible. Additional gain provided by the amplifier will reduce the S/N ratio by a similar amount, since the input noise figure is constant. Other values for R1 and R3 of between 1k and 10k ohm can be used if an intermediate gain level is necessary.
If driving a pair of headphones, you may also need a 100 ohm resistor in series with each output to reduce the output level, depending on headphone impedance & sensitivity. Make positive you start with the volume right down to check. Numerous headphones may be driven from the amplifier in the event you wish, since most headphones have at least 16 ohm impedance, or more often 32 ohm.
There are only a few outside parts, the IC contains most of the necessary schemary. R1,R2 and R3,R4 are the feedback resistors. C1 provides power supply decoupling. C2 and C3 are the input coupling capacitors, which block any DC that might-be present on the inputs. C4,C5 block DC in the feed back schema from the inverting inputs, and C6,C7 are the output coupling capacitors. C8, R5 and C9,R6 act as Nobel networks providing a high frequency load to maintain stability at frequencies where loud speaker inductive reactant may become excessive. The pot provides adjustable input level attenuation.
Sunday, September 14, 2014
4 x 70 W Power Amplifier TDA7563
Features:
DMOS POWER OUTPUT
■ NON-SWITCHING HI-EFFICIENCY
■ HIGH OUTPUT POWER CAPABILITY 4x28W/
4Ω @ 14.4V, 1KHZ, 10% THD, 4x40W EIAJ
■ MAX. OUTPUT POWER 4x72W/2Ω
■ FULL I2C BUS DRIVING:
– ST-BY
– INDEPENDENT FRONT/REAR SOFT PLAY/
MUTE
– SELECTABLE GAIN 30dB
– 16dB (FOR LOW NOISE LINE OUTPUT
FUNCTION)
– HIGH EFFICIENCY ENABLE/DISABLE
– I2C BUS DIGITAL DIAGNOSTICS
■ FULL FAULT PROTECTION
■ DC OFFSET DETECTION
■ FOUR INDEPENDENT SHORT CIRCUIT
PROTECTION
■ CLIPPING DETECTOR PIN WITH
SELECTABLE THRESHOLD (2%/10%)
■ ST-BY/MUTE PIN
■ LINEAR THERMAL SHUTDOWN
■ ESD PROTECTION
Circuit Diagram:
DMOS POWER OUTPUT
■ NON-SWITCHING HI-EFFICIENCY
■ HIGH OUTPUT POWER CAPABILITY 4x28W/
4Ω @ 14.4V, 1KHZ, 10% THD, 4x40W EIAJ
■ MAX. OUTPUT POWER 4x72W/2Ω
■ FULL I2C BUS DRIVING:
– ST-BY
– INDEPENDENT FRONT/REAR SOFT PLAY/
MUTE
– SELECTABLE GAIN 30dB
– 16dB (FOR LOW NOISE LINE OUTPUT
FUNCTION)
– HIGH EFFICIENCY ENABLE/DISABLE
– I2C BUS DIGITAL DIAGNOSTICS
■ FULL FAULT PROTECTION
■ DC OFFSET DETECTION
■ FOUR INDEPENDENT SHORT CIRCUIT
PROTECTION
■ CLIPPING DETECTOR PIN WITH
SELECTABLE THRESHOLD (2%/10%)
■ ST-BY/MUTE PIN
■ LINEAR THERMAL SHUTDOWN
■ ESD PROTECTION
Circuit Diagram:
![]() |
| Circuit diagram 4 x 70 W Power Amplifier TDA7563 |
Wednesday, September 10, 2014
1 W mini audio amplifier circuit
In this circuit requires only three components , namely IC TDA7052 , and 2 capacitor electrolyte. Actually , only with IC we are able to run this amplifier , but the sound less than the maximum. This amplifier circuit requires a minimum voltage of 3 volts and 15 volts maximum. Was 1 Watt power output with 4 Ohm impedance. See this circuit below :
![]() |
| Just IC and 3 components we can make the circuit above. |
Friday, September 5, 2014
TDA8551 Audio Ampllifier 1 x 1 W
TDA8551general description:

The TDA8551; TDA8551T is a one channel 1 W Bridge-Tied Load (BTL) audio power amplifier capable of delivering 1 W output power to an 8 Ω load at THD = 10% using a 5 V power supply. The circuit contains a BTL power amplifier, a digital volume control and standby/mute logic. The TDA8551T comes in an 8 pin SO package and the TDA8551 in a 8 pin DIP package.
TDA8551 features:
- One pin digital volume control
- Volume setting with UP/DOWN pulses
- Flexibility in use
- Few external components
- Low saturation voltage of output stage
- Standby mode controlled by CMOS compatible levels
- Low standby current
- No switch-on/switch-off plops
- High supply voltage ripple rejection
- Protected against electrostatic discharge
- Outputs short circuit safe to ground, VP and across the load
- Thermally protected.
TDA8551aplications:
- Portable consumer products
- Personal computers
- Telephony
TDA8551circuit diagram:

TDA8551pcb layout:

Thursday, August 28, 2014
2 x 75 W Audio Power Amplifier TDA7575
Features:
- DMOS POWER OUTPUT
- NON-SWITCHING HI-EFFICIENCY
- SINGLE-CHANNEL 1Ω DRIVING CAPABILITY
- HIGH OUTPUT POWER CAPABILITY 2x28W/
- 4Ω @ 14.4V, 1KHZ, 10% THD, 2x40W/4Ω EIAJ
- MAX. OUTPUT POWER 2x75W/2Ω, 1x150W/1Ω
- SINGLE-CHANNEL 1Ω DRIVING CAPABILITY
- 84W UNDISTORTED POWER
- FULL I2C BUS DRIVING WITH 4 ADDRESS
- ST-BY, PLAY/MUTE, GAIN 12/26dB, FULL
- DIGITAL DIAGNOSTIC
- POSSIBILITY TO DISABLE THE I2C
- DIFFERENTAL INPUTS
- FULL FAULT PROTECTION
- DC OFFSET DETECTION
- TWO INDEPENDENT SHORT CIRCUIT
- CLIPPING DETECTOR PIN WITH SELECTABLE THRESHOLD (2%/10%)
- ST-BY/MUTE PINS
Block Diagram:
![]() |
| Block Diagram |
Subscribe to:
Posts (Atom)


