Showing posts with label switching. Show all posts
Showing posts with label switching. Show all posts

Sunday, November 2, 2014

Variable switching power supply using LM317

Another power supply electronic circuit that is designed using LM317 voltage regulator can be designed using few electronic parts . This power supply circuit is a very simple low cost switching regulator electronic project that is based on the LM317 three terminal regulator .
As you can see in the circuit diagram this power supply electronic project require few external components and a LM317HV regulator . The input voltage required by this electronic project must be between 8 and 35 volt , and will provide a variable output voltage over a wide range , from 1.8 volts up to 32 volts
The maximum output current that can be delivered by this LM317HV switching power supply electronic project is up to 3 amperes .
C1 , C4 capacitors must be a solid tantalum type and L1 coil must have a 600uH inductance . For L1 coil you can use a Arnold A-254168-2 core with 60 turns .
 
 
 
 
 
 
 
 
  
Here continue read..

Saturday, October 18, 2014

LM2577 and LM2575 Switching Regulators

Switching regu­lators are available is different circuit configurations in­cluding the flyback, feed-forward, push-pull, and non-iso­lated single-ended or single-polarity types. Also, the switching regulators can operate in any of three modes – step-down, step-up, or polarity inverting.
rovide the active functions for step-down (back) switching regulator, capable of driving a1A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, 15V and an adjustable output version.


Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation and a fixed-frequency oscillator. LM 2575 series offers a high-efficiency replacement for popular 3-terminal linear regulators. It substantially reduces the size of the heat sink, and in many cases no heat sink is required. Fixed output voltage version is illustrated in figure.

The National Semiconductor LM 1577/LM 2577 are monolithic ICs that provide all of the power and control functions for step-up (boost), fly back, and forward converter switching regulators. The device is available in three different output voltage versions: 12 V, 15 V and adjustable.

Read more: http://www.circuitstoday.com/switching-regulators-using-lm-2575-and-lm-2577
Under Creative Commons License: Attribution
Here continue read..

Friday, October 17, 2014

12V 10Amp MJ2955 Switching Power Supply

The switching power supply provides 12 volts, at 10 amps, maximum, using a discrete transistor regulator with an op-amp functioning as a comparator in the feedback circuit.

With reference to the schematic, the front panel power-on light is not shown. There is no adjustable current limiter in this unit, although R1, R2, R3, Q2, R8, R9, C5 and Q4 set the current limit to approximately 10 amps. As you can see, the design is very similar to that of a linear power supply, except that L1, and D1 have been added, and U1 operates in a switching mode as a comparator with a small amount of hystersis. The switching frequency of this unit varies with the output current drawn by the load. This is an undesireable feature, which is why PWM regulators are used today. With a PWM regulator, the switching frequency is constant and will produce spurs only at known discrete frequencies rather than spurs at all frequencies. The Darlington-connected pass transistor block in the schematic is there twice (in parallel) for robustness. R4 in an internal trim-pot that can set the output voltage anywhere between 5 to 15 volts. 
Here continue read..

Sunday, October 5, 2014

Modular Preamplifier Switching Center

Modular

Parts:

R1,R2,R3,R4____100K 1/4W Resistors
R5_____________560R 1/4W Resistor

SW1,SW2________2 poles 4 ways Rotary Switches

J1 to J6_______RCA audio input sockets

Comments:

This module can be a necessary addition to the Modular Preamplifier Control Center when more than two sources need to be connected to the preamplifier chain.
Four high level inputs can be selected by means of SW1 and routed to the output. The output of this module must be connected by a suitable cable to one of the two inputs of the Control Center module. In this way, a total of five inputs will be available to the user of this module combination.

The Switching Control features also the so called "Double Bar", i.e. the possibility of routing to an external unit, e.g. a recorder (tape or digital) an input signal different from that reproduced at the time by the amplifier.
For example, you can listen in to a CD whereas the signal coming from a radio station through the Tuner is routed to the recorder. This selection is operated by means of SW2.

As with the other modules of this series, each electronic board can be fitted into a standard enclosure: Hammond extruded aluminum cases are well suited to host the boards of this preamp. In particular, the cases sized 16 x 10.3 x 5.3 cm or 22 x 10.3 x 5.3 cm have a very good look when stacked. See below an example of the possible arrangement of the front and rear panels of this module.

Here continue read..

Sunday, August 31, 2014

Simple 12 Volt 2 A Switching Power Supply Wiring diagram Schematic

This is a Simple 12 Volt / 2 A Switching Power Supply Circuit Diagram. The schema 12 volt / 2 A switching power supply in the above scheme is not too complicated. At the output of this block provides a stable 12 V and maximum current 2A. Power supply units are quite compact and is suitable for debugging schemes, as well as a permanent resource for stationary devices, including power for the logic electronics for the home-made ​​CNC machine tools. 

12 Volt / 2 A Switching Power Supply Circuit Diagram


12
 
 Transformer is available in the free market and avoids the hassle of having to self-winding. The diode bridge BR 1 of any given voltage and current of 2A. All other elements in the high part of the schema are designed by the same voltage, taking into account the mains. The scheme of 12 volt / 2 A switching power supply operates from the high voltage network, to be observed when mounting accuracy and caution when using. It is desirable to block the finished board to “pack” in the body. 

Sourced By :  powersupply88
Here continue read..