Showing posts with label low. Show all posts
Showing posts with label low. Show all posts

Thursday, October 30, 2014

Low Output Power Amplifier


This Low Output Power circuit was a presented,it can go power output around 1 Watt, whilst connected to a power supply 9 volt. The pro of this Low Output Power Amplifier is with the purpose of it uses a dual dear ton to enhance the size at the same time as much as of input impedance about 20 Meg ohm. This circuit unlike other circuits,the input impedance is a constant about 20 Meg ohm each time, whether to adjust the volume control on several level.

Low
Low Output Power Amplifier Diagram Schematic
The components participating in the circuit, it is tightfisted, especially the BC549 transistor output amount after the increase force be present very distorted, it have got to reduce the current level to a safe By dipping the volume down. The sector output in place of the R1 and C1 in order to reduce the oscillator profit is, the truth to the output sector, with an op-amp acts drive dual complementary.
Here continue read..

Thursday, October 16, 2014

Simple Battery Low Voltage Beeper Circuit

Simple Battery Low Voltage Beeper circuit provides an audible and visual low voltage warning for 12V battery powered devices. When the battery voltage is above the set point (typically 11V), the circuit is idle. If the battery voltage should fall below the set point, the LED will light and the speaker will emit a periodic beeping sound to warn of the impending loss of power. The circuit was designed for monitoring solar systems, but it could also be useful for automotive and other 12V applications.

Specifications:
  • Nominal operating voltage: 12V
  • Idle current: 6ma
  • Low Voltage Warning current: 15ma
Theory:
U2 provides a 5V regulated voltage reference. U1 is wired as a comparator, it compares the fixed 5V regulated voltage to the voltage on the wiper of VR1, that is proportional to the 12V supply. When the supply drops below the set point, the output of U1 goes low, turning on Q1 and powering the beeper and the LED.

The beeper consists of U4, a tone generator, and U3, a low duty cycle pulse generator. The tone can be changed by adjusting R7, the beep rate can be changed by adjusting R5. A small amount of hysteresis is provided by R1 and the current through LED1 and the beeper, this separates the on and off points for the circuit.

Battery Low Voltage Beeper Circuit


Simple Battery Low Voltage Beeper circuit board was made by printing the pattern (see below) onto Press-n-peel blue circuit board transfer film with a laser printer. Etch the board, drill the holes, and assemble the parts on the board as per the board photo. Be sure to correctly orient the diode, electrolytic capacitors, ICs, and transistor. The CA3160 op-amp may be difficult to find, other low power CMOS op-amps may be substituted. A standard 741 op-amp would also work, but the idle current will be higher.

Alignment:
Connect the circuit to an adjustable DC voltage source. Set the voltage source to 11V or wherever you would like the circuit to turn on. Turn on switch S1. Adjust VR1 until the point where LED1 just comes on and the beeping starts.

Use:
Connect the circuit to the 12V source that you wish to monitor. There should be a fuse somewhere between the battery and this circuit. Turn S1 on, if the battery voltage is above the set point, nothing should happen.
As the battery voltage drops below the set point, the LED will light and a periodic beeping will come from the speaker. If the beeping becomes annoying, turn off S1. Be sure to charge the battery soon, excessive discharging will shorten the life of most rechargeable batteries.
Here continue read..

Saturday, September 13, 2014

LM389 low power audio amplifier

Amplifier circuit below represents a very small amplifier circuit output. Maximum output is no more than 1W, comprehension is low but received a series of sensitive enough, and power amplifier circuit is very suitable for use in radio receiver, especially on FM radio.

Technical information.
Minimum Voltage = 4 Volt DC
Maximum Voltage = 15 Volt DC
Power Output         = 0,325 W
RL                          = 8 Ohm
Ft                            = 40Hz - 18KHz
Icco                        = 6mA

Part List :
R1 = 100K
R2 = 2,7R
R3 = 1K
C1 = 100uF
C2 = 220uF
C3 = 47uF
C4 = 0,01uF
Here continue read..

Build a Low Frequency Receiver Wiring diagram Schematic

Build a Low Frequency Receiver Circuit Diagram. Using an NE602 hetero dyne detector and Ul as an RF amplifier, this receiver tunes the middle portion of the low-frequency spectrum from 150 to 250 kHz. U2 is a loudspeaker amplifier. 

Build a Low Frequency Receiver Circuit Diagram

Build

Here continue read..

Friday, June 6, 2014

Arduino Based Low Power Wireless Solution

panStamp is an open source project created for the enthusiasts that love measuring and controlling things wirelessly. panStamps are small wireless boards specially designed to fit in low-power applications, simple to program and simple to work with. With panStamps, you can measure almost everything by simply connecting your panStamp to the sensors, placing a battery and sending wireless data from the first moment.


Arduino Based Low-Power Wireless Solution

panStamps are suitable for any kind of project needing remote control and low-power wireless transmissions, including home automation, energy metering, weather monitoring and robot control. If you are one of these three things: a hobbyist, a professional or an end-user, you will find that panStamps provide extreme flexibility and power when creating custom wireless networks. [Link]
Here continue read..