Showing posts with label using. Show all posts
Showing posts with label using. Show all posts

Monday, November 17, 2014

DC Motor Speed Control using PWM

DC Motor Speed Control using PWM

The so-called PWM or Witdh modulation is a technique often used to control a load, for example, is the control of DC motor speed PWM techniques are used frequently.

Usually to make a simple PWM (for practice or the introduction PWM) fans to use some of the facts of the op-amp circuit, which consists of Schmitt Trigger circuit, the integrator and comparator.


Schmitt Trigger function that produces a square wave will become the sawtooth wave or integrator is also called common rail and the ramp compared to a reference voltage that can change a lot of stress. So the result is a PWM output.


These two schemes are variations of different circuit PWM. The diagrams are for 12V operation and there are upper (ground) and low side (+12 V common) versions. The version of the lower circuit uses an N-channel FET, the high-side version of the circuit uses a P-channel FET. N channel devices tend to handle more current P-channel devices, which are also less expensive. The version of the high side of the circuit is useful when a portion of the load must be grounded.

This circuit can change a fairly high amount of current, a MOSFET IRFZ34N can handle over 35 Amps if connected to an adequate heat sink. Higher power FETs, such as IRF1010Z IRFZ48N or can be substituted if even larger currents are required. It is also possible to connect multiple FETs in parallel even more current capacity. Always use thermally conductive grease between the FET and the heat sink, and remember that the heatsink is under stress.

Inductive loads (motors) may require special care because it can generate large voltage spikes that can damage the MOSFET. Replacing a 1N4002 fast recovery diode can help absorb the recoil reverse voltage when driving an inductive load like a motor. If you use these circuits to experiment with electric vehicles, be sure to install a circuit breaker in series with the battery, the switch should be easy to reach by the driver. This is especially important given the fact that when non-MOSFETs, is often cut, leaving the engine running at full speed
Here continue read..

Thursday, November 13, 2014

using LM741 Simple Electronic Bell Generator

Today I begs for to advise Simple Electronic Bell Generator , with Linear IC Op-Amp the number is highly popular be number LM741. By when press S1 as a result , will have sound signal bell come out and lead this signal goes to amplify talk at one time with power Amplifier Circuit The general. For Circuit the this friends must use Dual Power supply Source 9 Volt. Detail sizes are other friends has seen in the circuit , which not difficult yes.

Here continue read..

Tuesday, November 4, 2014

Fire Alarm Using Thermistor

Small and simple unit, Can be used for Home-Security purpose. In this fire alarm circuit, a Thermistor works as the heat sensor. When temperature increases, its resistance decreases, and vice versa. At normal temperature, the resistance of the Thermistor (TH1) is approximately 10 kilo-ohms, which reduces to a few ohms as the temperature increases beyond 100 C. The circuit uses readily available components and can be easily constructed on any general-purpose PCB.

Fire Alarm Using Thermistor Circuit diagram:

Fire

Parts Description
R1 470R
R2 470R
R3 33K
R4 560R
R5 470R
R6 47K
R7 2.2K
R8 470R
C1 10uF-16V
C2 0.04uF-63V
C3 0.01uF-63V
Q1 BC548
Q2 BC558
Q3 SL100B
D1 Red Led
D2 1N4001
IC1 NE555
SPKR 1W-8R
TH1 Thermistor-10K

Circuit Operation:


Timer IC NE555 (IC1) is wired as an astable multivibrator oscillating in audio frequency band. Switching transistors Q1 and Q2 drive multivibrator IC1. The output of IC1 is connected to NPN transistor Q3, which drives the loudspeaker (SPKR) to generate sound. The frequency of IC1 depends on the values of resistors R6, R7 and capacitor C2. When Thermistor TH1 becomes hot, it provides a low-resistance path to extend positive voltage to the base of transistor Q1 via diode D2 and resistor R3. Capacitor C1 charges up to the positive voltage and increases the ‘on’ time of alarm. 

The higher the value of capacitor C1, the higher the forward voltage applied to the base of transistor Q1. Since the collector of transistor Q1 is connected to the base of transistor Q2, transistor Q2 provides positive voltage to reset pin 4 of IC1. R5 is used such that IC1 remains inactive in the absence of positive voltage. D2 stops discharging of capacitor C1 when the Thermistor connected to the positive supply cools down and provides a high-resistance (10k) path. It also stops the conduction of Q1. To prevent the Thermistor from melting, wrap it up in mica tape. The circuit works off a 6V-12V regulated power supply. D1 is used to indicate that power to the circuit is switched on.


Here continue read..

Sunday, November 2, 2014

Variable switching power supply using LM317

Another power supply electronic circuit that is designed using LM317 voltage regulator can be designed using few electronic parts . This power supply circuit is a very simple low cost switching regulator electronic project that is based on the LM317 three terminal regulator .
As you can see in the circuit diagram this power supply electronic project require few external components and a LM317HV regulator . The input voltage required by this electronic project must be between 8 and 35 volt , and will provide a variable output voltage over a wide range , from 1.8 volts up to 32 volts
The maximum output current that can be delivered by this LM317HV switching power supply electronic project is up to 3 amperes .
C1 , C4 capacitors must be a solid tantalum type and L1 coil must have a 600uH inductance . For L1 coil you can use a Arnold A-254168-2 core with 60 turns .
 
 
 
 
 
 
 
 
  
Here continue read..

Wednesday, October 8, 2014

Serial Voltmeter using the PIC16C71

Serial

Building a serial voltage meter to measure from 0 to 5 volts DC is actually pretty easy. Using MeLabs PicBasic, and Microsoft’s Visual Basic Version 5 Pro. You need Visual Basic Pro version because you will have to use Basic’s MSComm control. This control is not available in the Visual Basic 5 “Learning” Edition. The PIC16C71 simplifies the task even more by having a built in A/D converter. Pins 17,18,1,2 are the analog inputs AIN0,AIN1,AIN2,AIN3 respectively.

Here continue read..

Friday, October 3, 2014

Simple LED Flasher Circuit Using 555 IC

This is a simple LED flasher project that built uses a common 555 timer IC for its operation. It is configured as an unstable mode which means that its output is a square wave oscillator. Two LEDs are connected to its output in such a way that when one LED is ON, the other LED will turn OFF. It circuit uses only 10 simple parts that are easily available at any electronic shops. This is the simple figure of the circuit;


Principle work of this circuit is capacitor C2 charges exponentially through resistors R1, R2 and the resistance of the variable resistor. When C2 has charged to about 2/3 VCC it stops charging and it discharges to about 1/3 VCC through R2 and the VR resistance via pin 7. This is the standard operation of a 555 timer. When a Vcc of 5 V to 15 V DC is applied to the circuit, the LED will start to flash. The frequency of the flashing can be changed by varying the resistance of the potentiometer.

Here continue read..

Wednesday, October 1, 2014

Simple Temperature Indicator Circuit Using LEDs

A simple temperature indicator circuit was required for a gas fridge in a caravan to show when the pilot light had gone out.
The sensing element used was a thermistor, attached to the outlet which is warm when the pilot light is on, A rod~type thermistor was used for cheapness, with a. resistance of about 3k atg20* CW Two gates of the 7400 provide a Schmitt trigger with a low hysterysis (determined by the 18k feedback resistor) and the third gate inverts that output, When the pilot light is on, the input of lC1a is high,. lC1c output is logic O and LED2 (green) is on. lf the pilot light `fails, the  temperature falls, all gates change state, LED2 goes off and LED1 (red) comes on.  The temperature at which the changeover takes place is set by the 1k preset. 


Here continue read..

Sunday, September 14, 2014

Frequency measurement using two timer

frequencyThis tutorial is about measuring the frequency of a signal.To count a signal frequency many techniques are available.After some googling results in a delay method which makes a 1 second delay, by the meantime a counter counts the pulses.Then the number of pules will be the frequency of the signal. But it makes some problem such as
  • When it makes delay microcontroller cpu is idle for 1 second.
  • It reduces the speed of the process.
  • Other works are stopped at the time of frequency measurement.
So we need a solution where we can measure frequency as well as all the problems will be solved.
Actually the solution is very easy.You have to use two timer at a time.One timer as a counter and another one is used to make a delay.As timer can run freely without disturbing the cpu and can generate interrupts so all problems will be vanished and calculation will be more accurate and smart.
In this tutorial PIC16f873 is used,codes are written in MikroC Pro For PIC ,whole project are simulated in Proteus 7.6. You can download the all the files (including ISIS schematic,MikroC Project files) from the link given below the post.
Here Timer1 is used to make a delay of 1 second.You can make any time delay using a timer just take help of a very good tool called Timer Calculator which can generate code according to your need. Just input your controller frequency,the timer you want to use,the time delay you want.According to my need it was like below
 image
Then just copy the code to your MikroC editor.Then initialize Timer0 as a counter.You have to write the code
T0CS_bit=1;
T0SE_bit=0;
TMR0IE_bit=1;
Now open the project file which you downloaded and build it.Open the .DSN schematic file in Proteus and load the hex.A pulse of frequency 1000Hz is fed to T0CKI pin.Then run the schematic.If there is no error then Lcd will show exactly 1000Hz.You can change the frequency.
frequency
You can add your code according to your project and just take the value of frequency when you need. If you have any problem to understand the tutorial please put a comment or mail me.Don,t forget to share the post.
Download the project files from here.
Here continue read..