Showing posts with label timer. Show all posts
Showing posts with label timer. Show all posts

Monday, November 17, 2014

Timer 555 Schematic

Simple Timer With 555 is one example of a simple timer and can be applied to electronic equipment. With 555 Timer Simple series takes advantage of the mode of the IC monostable multivibrator 555. With the relay output control circuit can be used to control equipment with AC voltage source. With 555 Timer Simple circuit can work with source voltage of 5 - 12VDC depending on the relay used. In order to use Simple Timer With this 555 can be started by pressing the switch S1 to start the process of timing. In the relay there are 2 options that is normaly Close connection (NC) and normaly open (NO).
Timer

The duration of the timing circuit 555 Simple Timer With RC configuration is determined by the VR 1 MOhm and C 10uF. Active timer duration can be calculated with the formula T = 1.1 RC where T (seconds), R (Ohm) and C (farad). To get more accurate results R and C components referred to in the formula should use good quality components, namely C of tantalum material and R with the quality of 1%.
Here continue read..

Tuesday, November 4, 2014

Touch Free Timer Switch

This type of infrared proximity circuit is widely used as an electric switch where physical contact is not desired for hygiene purpose. For example, we commonly see use of infrared proximity sensors on public drinking fountains and in public washrooms. The simple circuit presented here can be operated by moving your hand in front of it. This is achieved by detecting the infrared light reflected by your hand onto a receiver device.

Fig. 1: Touch-Free Timer Switch Circuit diagram :

Timer

Fig. 1 shows the circuit of the touch-free timer switch. It has two sections: transmitter and receiver. The IR transmitter is built around timer LMC555 (IC1), which is wired as an astable multivibrator. The multivibrator produces 38kHz pulses (at low duty cycle) that drive an infrared LED (LED1). This frequency can be tuned using a 10-kilo-ohm preset (VR1). A 220-ohm series resistor (R3) ensures that the current consumption of the IR transmitter is not out of arrangement.

The receiver section is built around IR receiver module TSOP1738 (IRX1), timer LMC555 (IC2) and a few discrete components. The TSOP1738 is an integrated miniaturised receiver for infrared remote control systems. Everything required for IR signal processing, including the PIN diode and preamplifier, are assembled on a lead frame and the epoxy package is designed as an IR filter.

When a short IR burst is received by IRX1 (as you wave your hand in front of the switch), the demodulated pulses are fed to the trigger input (pin 2) of the second LMC555 (IC2). This, in turn, triggers the monostable wired around IC2 and its output pin 3 goes high for a period determined by the 2.2-mega-ohm potentiometer and capacitor C5. This turns off the standby indicator (LED1) and transistor T1 conducts to drive the 5V relay (RL1). LED1 enables you to locate the switch in the dark. AC mains supply to the load to be switched-on is routed through the pole and normally-opened contacts of RL1 as shown in the diagram. The circuit works off regulated 5V DC.

Fig. 2: Pin configurations of TSOP1738, IR LED and BC547

Pin

Fig. 2 shows the pin configurations of TSOP1738, IR LED1 and transistor BC547. Assemble the circuit on a general-purpose PCB and enclose in a small plastic cabinet. Fit IR LED1 with a reflecting hood at a recessed position on the front panel of the enclosure. The dome-shaped face of the TSOP1738 should stick out from the front panel. Fit the time-control potentiometer (VR2) in an appropriate position. Finally, fit the standby indicator LED1 inside a suitable LED holder such that it slightly protrudes from the front panel. To prevent unwanted reflection of the IR beam, the finished unit should be mounted such that it does not face a nearby wall.

 Fig. 3: Suggested enclosure


Suggested

Using high-precision linear potentiometer VR2 and capacitor C5 (100µF), the time length can be set from nearly 1 second to 120 seconds. Attach a small paper dial on the front panel of the enclosure and mark various positions of the control knob of VR2 as shown in Fig. 3. The accuracy of the timer depends mainly upon the quality (and value) of timing capacitor C5. In practice, most electrolytic capacitors are rated on the basis of minimum guaranteed value and the real value may be higher.


Here continue read..

Sunday, September 14, 2014

Frequency measurement using two timer

frequencyThis tutorial is about measuring the frequency of a signal.To count a signal frequency many techniques are available.After some googling results in a delay method which makes a 1 second delay, by the meantime a counter counts the pulses.Then the number of pules will be the frequency of the signal. But it makes some problem such as
  • When it makes delay microcontroller cpu is idle for 1 second.
  • It reduces the speed of the process.
  • Other works are stopped at the time of frequency measurement.
So we need a solution where we can measure frequency as well as all the problems will be solved.
Actually the solution is very easy.You have to use two timer at a time.One timer as a counter and another one is used to make a delay.As timer can run freely without disturbing the cpu and can generate interrupts so all problems will be vanished and calculation will be more accurate and smart.
In this tutorial PIC16f873 is used,codes are written in MikroC Pro For PIC ,whole project are simulated in Proteus 7.6. You can download the all the files (including ISIS schematic,MikroC Project files) from the link given below the post.
Here Timer1 is used to make a delay of 1 second.You can make any time delay using a timer just take help of a very good tool called Timer Calculator which can generate code according to your need. Just input your controller frequency,the timer you want to use,the time delay you want.According to my need it was like below
 image
Then just copy the code to your MikroC editor.Then initialize Timer0 as a counter.You have to write the code
T0CS_bit=1;
T0SE_bit=0;
TMR0IE_bit=1;
Now open the project file which you downloaded and build it.Open the .DSN schematic file in Proteus and load the hex.A pulse of frequency 1000Hz is fed to T0CKI pin.Then run the schematic.If there is no error then Lcd will show exactly 1000Hz.You can change the frequency.
frequency
You can add your code according to your project and just take the value of frequency when you need. If you have any problem to understand the tutorial please put a comment or mail me.Don,t forget to share the post.
Download the project files from here.
Here continue read..

Wednesday, September 3, 2014

Simple Ignition Timer Wiring diagram Schematic

This schema is a tester for flywheel based ignition systems in small aeroplane engines. Basically the same ignition coils are also seen in other small combustion engines used in/on mopeds and lawn mowers  in brief, engines without a battery. The part to be tested comprises a primary coil in parallel with the contact breaker. The timing of this contact breaker has to be adjusted correctly.
Since the coil’s primary has a very low resistance it is difficult to determine whether the contact breaker is open or closed.  However, you can determine that reliably with this schema, using an LED and a beeper. The schema is implemented twice because aviation engines (Cessna, Piper and similar) always have two ignitions in parallel to increase reliability. For two-cylinder engines, well the purpose is obvious.

Ignition Timer Circuit Diagram
Simple

The schema consists of a 555 and a few transistors. The 555 supplies a square wave of about 3000 Hz. This signal goes to power transistors T1 and T2; these can supply quite a bit of power and are robust enough to withstand the voltage transients from the big coils. The test connection (K2 and K3 respectively) are connected in parallel with the contact breaker to be tested, which itself is in parallel with the ignition coil. The frequency of 3000 Hz is either short schemaed by the contact breaker or if the points are open  is amplified somewhat by the resonance of the coil itself.

This allows you to reliably detect the difference bet ween a closed and open contact breaker, despite the low resistance of the coil, which is in parallel with it. When the contact breaker is open the amplified pulses will turn on T3 and T4 respectively, so that the relevant LEDs turn on and the buzzer will sound.

The components are not critical, but do use a sensitive type for the piezo buzzer. The power supply is 3 V (2 times AA or AAA batteries). 
Here continue read..

Wednesday, August 13, 2014

PCB Exposure Switch Timer V2 0

After some modifications on my UV exposure box (scanner) for better UV expose, i decided that a better pcb must me designed for switch timer. The old one had over drilled holes and it was designed and built on my very fist steps. Also the high voltage side from the low voltage wasn’t separated as it needed to be safe.
PCB Exposure Switch Timer V2.0

So i redesigned it in a more compact and easier to use pcb. The firmware has been also updated and now you can program the timmer by using the two buttons. The time is calculated by timer interrupt triggering using a 32.768KHz RTC Crystal with better accuracy. The display update also has been changed from static to dynamic. [Link]
Here continue read..